Deepthi. C.P.

A Chemical Engineering graduate with 16 years of experience, seeking a creative and challenging position as a Chemical Engineer or Process Engineer in the refining, petrochemical, or any other chemical industry. I aim to leverage my engineering, technological, and interpersonal skills to contribute effectively to the growth and success of the organization.

Sagaciter Process Technologies LLP (Subsidiary of Technomak Process Systems FZC)

Senior Process Engineer | Cochin | May 2023 – Present

Engaged in detailed engineering activities including:

Process Studies Reports, Process Design Basis, Process Descriptions

Process Flow Diagrams (PFD), Heat and Material Balance, Utility Balance

Process Safeguarding Diagrams, Material Selection Diagram

Operating and Control Philosophy, Cause & Effect Diagrams

Equipment List, Equipment Sizing Calculations, Process Equipment Data

Relief Valve Sizing Calculations, Line Sizing and Hydraulics

Process Simulations

Petrocil Engineers & Consultants Pvt Ltd

Senior Process Engineer | Cochin | April 2019 – May 2023

Involved in detailed engineering activities including:

Process Studies Reports, Process Design Basis, Process Descriptions

Process Flow Diagrams (PFD), Heat and Material Balance, Utility Balance

Process Safeguarding Diagrams, Material Selection Diagram

Operating and Control Philosophy, Shutdown Philosophy, Relief and Blowdown Philosophy

Pre-commissioning & Commissioning Philosophy, Isolation & Sparing Philosophy

Process & Utility System P&IDs, Cause & Effect Diagrams

Equipment List, Equipment Sizing Calculations, Process Equipment Data

Relief Valve Sizing Calculations, HAZOP Closeout Reports, Process Simulations

Tek Path Consultants & Engineers Pvt Ltd

Process Engineer | Cochin | Oct 2014 – Aug 2015

Reliance Industries Limited (RIL)

Technical Service Engineer | Vadodara Manufacturing Division (VMD) | June 2007 – April 2014

Worked in the Low-Density Polyethylene (LDPE) Polymer Plant

Key Responsibilities:

Plant monitoring, deviation analysis, troubleshooting, and corrective actions

Optimization, efficiency improvement, and debottlenecking

Updating Piping & Instrumentation Diagrams (P&ID) & Process Flow Diagrams (PFD)

Reviewing and updating Standard Operating Procedures (SOPs)

Material & Energy balance preparation for plant capacity assessment

Adequacy checking of Pressure Safety Valves (PSVs) for higher capacity operations

Development of process simulation models for process design, troubleshooting, and new projects

Identifying and implementing profit improvement opportunities

Process Engineering Project:

Provision of an additional recycle gas cooler at the feed compressor suction, increasing production by 1000 MT per annum

Developed a simulation model for the ethylene feed hyper compressor

Participation in turnaround activities and failure analysis

Good knowledge of Process Safety Management (PSM)

Active member of the Process Hazard Analysis (PHA) committee

Process design for Management of Change (MOC) and vendor technical evaluations

Failure analysis and corrective action recommendations

Achievements:

Represented RIL at the Global 21st Annual PEPP Chain Conference in Amsterdam

Reliance Industries Ltd, Hazira

Project Engineer – Cyclohexane Plant | Hazira

Involved in pre-commissioning & commissioning of the Cyclohexane plant

Worked as a panel operator for six months

Kerala State Pollution Control Board

Graduate Engineering Apprentice | March 2007 – June 2007

Hindustan Organic Chemicals Ltd, Cochin

Graduate Apprentice | Dec 2005 – Dec 2006

Prepared daily production and consumption reports

Bachelor of Technology (B.Tech) in Chemical Engineering
Government Engineering College, Calicut
University of Calicut, India
Score: 60.75%

Pre-Degree
Government College, Malappuram
University of Calicut, India
Score: 80%

S.S.L.C (Secondary School Leaving Certificate)
St. Gemma’s Girls High School, Malappuram, Kerala
Score: 88%

Skills & Competencies

Professional Skills

Process Engineering & Design

Plant Operations & Troubleshooting

Process Optimization & Debottlenecking

Safety & Risk Assessment (HAZOP, PHA)

Simulation & Modeling

Technical Documentation & Report Preparation

Software Proficiency

Process Simulation: ASPEN Plus, HYSYS (Familiar)

Process Safety Analysis: PHAST, PHA Works

Engineering & Drafting: AutoCAD

Computer Proficiency

Operating System: Windows

Office Tools: MS Office (Word, Excel, PowerPoint)