Mastan Basith

MEP Engineer experienced in design and maintenance of mechanical, electrical and plumbing systems. Interpreted architectural designs and engineering schematics to best route electrical and plumbing. Updated designs with as-built drawings and entered data into GIS systems for facility maintenance. Sought solutions for issues concerning High Rise Buildings, Hospitals and Pharma. MEP Engineer experienced formulating cost estimates while working under tight budget constraints Selected high-quality products and materials for projects without breaking budget. Inspected and evaluated facilities for compliance to design and codes and to inspire future projects.

Senior MEP Engineer at Abdulrahman Bin Abdulaziz for Cont. & Trans.L.L.C ,, Doha

January 2018 — February 2023

• To work closely with the Head of Projects in implementing the MEP works in the site. Evaluate projects along with Designers, Architects & Project Managers.
• Coordinate with the in-house Design Management department 
  on project Electrical /Plumbing/Firefighting issues.
• Material procurement evaluations of Mechanical/Electrical/Plumbing from Vendors
• To estimate the budget and to control in implementing MEP works in the site
• Responsible for technical evaluations of Mechanical/Electrical/Plumbing for Vendor quotations.
• Reviews project contract documents and monitors construction activities to ensure compliance
• Monitors and/or evaluates electrical tests such as ground-fault, ground resistance, insulation resistance, polarity, continuity, capacity, load and other electrical field tests as required.
• Exercises ability to interpret single-line and/or schematic electrical drawings as well as plans and specifications.
• Field checks installation and location of electrical equipment, electrical duct, conduit, cable, panels and other components of the electrical system being installed. Assures compliance with approved submittals.
• Based on design proposals, carry out techno-commercial negotiations for various MEP works.
• Monitors all electrical installations to assure circuitry phasing, equipment, and grounding adhere to construction documents and National Electric Code requirements.
• To Evaluate Mechanical design documents, specifications, BOQs, variations, scope of works according to standards, regulations and as per the site conditions.
• Verifies equipment settings, alignment, and testing and energization requirements.
• Provides general inspection on all contractor and subcontractor work to assure a safe and workman like operation.

MEP Engineer at Khalifa Electro-Mechanical Engineering Services , Doha

October 2015 — January 2018

• Preparation   of shop drawing on AutoCAD for HVAC, Fire Fighting, Electrical &   Plumbing.
• Preparation   of HVAC,   Domestic Water Supply, Sanitary, Drainage &   Fire   Fighting  drawings etc.
• Preparation   of Electrical
• Installation   of HVAC, Plumbing & Fire Fighting works and Co-ordination, with   Consultant, Architect for execution of site work and Material Approval.
• Inspection   and Supervision on site as per approved shop drawing and coordinating with   Supervisors to solve the problem related with Design and Drawing.
• Preparation   of Landscaping, Drainage, Surface Water Site Plan Drawing. etc.
• Prepare   progress report and other related reports during all stages of constructions.
• Co-ordination   with suppliers to ensures correct and timely delivery of materials
• HVAC:
• Responsible   for designing of Plumbing systems, HVAC System & Fire Fighting.
• Design   HVAC System for Wall Mounted Split unit, duct able Split Unit & Package   Unit with required capacity.
• Design   HVAC System of capacity up to 50 TR.
• Preparation   of Duct design & duct size calculation.
• Preparation   of Material Submittal, Method Statement, Shop drawing, Project Schedule and   planning.
• Handled   multiple projects simultaneously.
• Manage   installation of ducts for ventilation purposes.
• Co-ordination   with consultant for submittal and approval of material equipment.
• Perform   regular inspection all materials and works for all plumbing activities.
• Execution   of Ducting, Piping, installation and commissioning of centralized air   conditioning, Splits and Package A/C units.

FIRE   FIGHTING:

• Design   Fire Fighting System for pipe, Hose reel, Sprinkler, FM200 &   Extinguisher.
• Design   and install fire safety equipment.

ELECTRICAL:

• Maximum   demand estimation and deciding voltage level.
• Design   of earthing & lightning protection system.
• Selection   of Transformer/DG capacity and number with necessary metering &   protection.
• Selecting   the location of load center & captive power generation station.
• Preparation   of detailed main single line schematic.
• Short   circuit & voltage drop calculation at each level of distribution.
• Design   of earthing & lightning protection system.
• Design   of fire safety in substation, cable trenches and other parts of electrical   system.
• Preparation   of Power & Control cable schedule.

Preparation of building plan &   equipment layout such as:

1. Point of supply and Cable trench layout.
2. DG & Main LT electrical room layout.
3. Earthing scheme & earthing layout
4. Lighting, Power& UPS layout with distribution scheme.

PLUMBING:

• Design   Plumbing systems including sanitary waste, vent, storm, domestic water   distribution systems, and purified water systems.
• Material   used in Plumbing System is PPR, PVC, CPVC & UPVC.
• Monitor   installation and perform tests on various water and sewage lines for all   residential and commercial buildings.
• Experience   with sanitary waste & vent, hot and cold water & storm water.

Mechanical Engineer - HVAC at Teena Labs, Hyderabad

October 2011 — October 2015

• Wrote   and revised maintenance procedures.
• Conducted   research to test and analyze feasibility, design, operation and performance   of equipment, components, and systems.
• Suggested   cost saving proposals on make-versus-buy analysis or alternative sourcing.

Evaluate

• Go   through requisite procedures, plan and prioritize activities for the day   based on work plan received from supervisor.
• Ensure   Supervision of preventive maintenance of process and utility equipment as per   the schedules.
• Supervision   of preventive maintenance / maintenance works of water systems.
• Supervision   of all maintenance works in shifts.
• Inspection   of the equipment / materials received at engineering stores.
• Verification   of quantity and quality of works done by all contractors.
• Ensuring   the usage of safety gadgets by work force.
• Ensuring   work permits raised for Hot work, work at height, vessel entry, general work   permits etc.
• Ensuring   the smooth operation & maintenance of water systems.
• Ensuring   the smooth operation & maintenance of HVAC systems.
• Timely   reporting of abnormalities/ Deviations to the immediate supervisor/   appropriate authorities

Documentation

• Ensure   and aware of plant and equipment layouts, block layouts, site layouts and   P&ID's for the documentation requirements.
• Updating   the documentation on daily basis which includes preventive maintenance,   history cards, Break down maintenance, qualification and SOPs.
• Preparation   of Validation schedules and execution as per the procedures.
• Preparation   of Master equipment lists in the plant as per the procedures.

Coordination

• Understand   the requirements of the User departments and prioritizing the works based on   the business need and urgency.

Training

• Successful   completion of assigned trainings and application of the same at workplace’s   final product's overall performance, reliability and safety.

Mechanical Engineer at HBL POWER SYSTEM PVT LTD, , NANDIGOAN 

August 2009 — October 2011

• Conducted   research to test and analyze feasibility, design, operation and performance   of equipment, components, and systems.
• Wrote   and revised maintenance procedures.
• Conducted   tolerance analysis at system and subsystem levels.
• Suggested   cost saving proposals on make-versus-buy analysis or alternative sourcing.
• Handling   of Installed equipment like DG Sets, Compressors, Boiler, DM Plant, Handling   every type of audit and inspection related to maintenance.
• Good   Knowledge of sterilizer Plant equipment - SS/GL reactors & Expertise in   the maintenance of weld shop.
• Preventive   Maintenance, predictive maintenance, and proactive maintenance of all plant   equipment.
• Handling   skilled manpower and administration of the entire department. Improvements in   a breakdown in the entire plant by Works' study.
• Preparing   and implementing action plans effectively to maximize the overall equipment   efficiency of production-related machines.
• Implementation   of Continuous Improvement related to cost, Quality, Morals, Safety and   Related Processes.
• Responsible   for documentation of maintenance work-related documents like (Skill Matrix,   Loss time Calculation, OEE (Overall Equipment Efficiency), daily breakdown   status, and daily overtime status.
• To   ensure zero breakdowns in working hours and also in odd hours.
• To   optimize productivity by various methods: - By continual Improvements,   Optimum utilization of all the resources 4Ms (Man, Machine, Material,   Method).
• Responsible   for Making Daily maintenance plans according to plant requirements   &Meeting daily breakdowns.
• Responsible   for Line balancing for new line & Existing production line. Organizing   quality circles in the department.
• Examine   the needs for training and provide on-the-job training to departmental   personnel.
• Troubleshooting   and solving technical problems.
• Analysis   of daily tool consumption and generation of maintenance reports. Preserve   discipline according to safety rules.

Ensure   inventory of Spare parts for plant equipment

Mechanical Engineer, PRRM Engineering college, Shabad

June 2005 — May 2009

Skilled at developing and testing equipment, creating detailed models and drawings, and completing ambitious projects on time and under budget. Equally effective in a leadership or hands-on role. Bachelor  Degree in Mechanical Engineering

MPC, Narayana Jr College , Nellore

June 2003 — May 2005

Xth Class(Matriculation), Deepika Memorial school , Shadnagar

June 2002 — June 2003